What is the maximum number of supported DAE's that can be attached to a Dell | EMC CX-400? v Three Two Five Four What is the default username and password for a Navisphere 6.x domain? v There is no default username and password. Username = admin and Password = password Username = Administrator and password = password Username = CLARiiON and password = CLARiiON! Which PowerPath command will manually restore the paths in PowerPath? powermt failback v powermt restore powerpath restore powermt trespass Which PowerPath license level is the minimum requirement to have front-end and back-end failover for a Dell | EMC CX700 installed in a Clariion only SAN? v PowerPath Enterprise PowerPath Base PowerPath Basic PowerPath Enterprise Plus Which EMC utility is used to manage Emulex HBAs? v Elxcfg Emconfig Emlxcfg Elconfig Which parameters are required When connecting to a Dell | EMC DS-16-B2 (Brocade 3800) with a serial cable? Null modem ?9600, 8, None, 1, Hardware Straight through cable ?2400, 8, None, 1, Hardware v Straight through cable ?9600, 8, None, 1, None Null modem ?2400, 8, None, 1, None Which storage processor port number on a CX600 is matched with worldwide port name xx:xx:xx:63:xx:xx:xx:xx? SPB port 2 v SPA port 3 SPA port 2 SPB port 1 Which command will retrieve Navisphere Agent information from a Dell | EMC CX-600's storage processor whose IP address is 10.38.45.76? navicli –h 10.38.45.76 get agent navicli –h 10.38.35.76 agentget v navicli –h 10.38.45.76 getagent navicli getagent –h 10.38.45.76 Which type of NaviSphere user account has read only rights on a CX700? Administrator Manager v Monitor Reader How many domains can a Dell | EMC CX-600 be a member of? Two Four Three v One How many longwave ISL's are required when cascading two Brocade DS32B2 switches? Only 1 is supported ! 1 minimum, 4 maximum ! 2 minimum, 4 maximum Only 2 are supported Which troubleshooting method is available for a Dell | EMC CX-600 but not for a Dell | EMC CX-400? POST Alphabet LED flash rate Monitoring POST with a hyperterminal session. v Port 80h codes Which of the following is the correct method for configuring the network settings on a new CX600 array's Storage Processors? Use a serial PPP session to configure SP-A and reboot it. Repeat the same configuration steps for SP-B. Use a serial PPP session to configure SP-A and reboot it. Do not configure SP-B because it will obtain its network settings from SP-A automatically. v Use a serial PPP session to configure SP-A and reboot it. Repeat for SP-B. Reconnect to SP-A using PPP and restart the management server on SP-A. Use a serial PPP session to configure SP-A and reboot it. Repeat for SP-B. Reconnect to SP-A using PPP and restart the management server. Repeat for SP-B Which of the following statements is true when cabling a Dell | EMC CX-400 for multipath? One HBA should see SPA_port_0 & SPA_port_1 while the other HBA should see SPB_port_0 & SPB_port_1 One HBA should see SPA_port_0 & SPB_port_0 while the other HBA should see SPA_port_1 & SPB_port_1 Both HBAs should see SPA_port_0 & SPB_port_0 and both HBAs should see SPA_port_1 & SPB_port_1 v One HBA should see SPA_port_0 & SPB_port_1 while the other HBA should see SPA_port_1 & SPB_port_0 In NaviSphere Manager, how is an old host de-registered from a CX600? ! A privilege user must highlight the old WWN and click de-register. A host can not be de-registered from an array. Through either Navicli or engineering mode. The host is automatically de-registered when it powered off. When installing a QLogic HBA in a Windows based server for direct attached storage, what must be true for the HBA's configuration? The QLogic Fabric - Auto Map driver must be installed. The Connection Type BIOS setting must be set to 0. ! The QLogic Loop - Auto Map driver must be installed. The Connection Type BIOS setting must be set to 1. Which procedure is correct for zoning a McData switch in a Dell | EMC environment? Create a zone, add the zone to the alias, add the alias to the config v Create a zone, add WWNs to the zone, add the zone to the zone set Create an alias, add the alias to the zone, add the zone to the config Create a zone, add ports to the zone, add the zones to the zone set What would the enclosure IDs be on a Dell | EMC CX700 array with 1 DAE-OS and 6 DAEs connected? v 0,0,0,0,1,1,1 0,1,2,3,4,5,6 0,1,2,3,0,1,2 0,0,1,1,2,2,3 How is the PSM LUN created on a Dell | EMC CX-600? The PSM LUN is created using the navicli command. The PSM LUN is created using the http://192.168.1.1/setup pages. The PSM LUN is created the first time you connect with Navisphere Manager. v The PSM LUN is created at the factory. What is the function of the watermark configuration setting on a CX400 in NaviSphere Manager? Establishes flushing priority for items stored in read cache Determines which data is overwritten when read cache is full ? Determines how frequently write cache is disabled when SPS auto-check occurs. Establishes flushing priority for items stored in write cache When replacing an HBA in a server installed in a Dell | EMC SAN, what must be done for PowerPath to recognize the path of the new HBA? Create a new zone for the HBA and add it to the existing configuration. Remove the zone from the configuration, re-add it, then click enable. v Remove the old member's WWN from the HBA's alias and add the new member's WWN. Disable the configuration, add a new alias for the HBA and click enable.