Which storage processor port number on a CX600 is matched with worldwide port name xx:xx:xx:63:xx:xx:xx:xx?

   SPB port 2 
   SPB port 1 
v  SPA port 3 
   SPA port 2 

Which PowerPath license level is the minimum requirement to have front-end and back-end failover for a Dell | EMC CX700 installed in a Clariion only SAN?

v  PowerPath Enterprise 
   PowerPath Base 
   PowerPath Basic 
   PowerPath Enterprise Plus 

Which of the following statements is true when cabling a Dell | EMC CX-400 for multipath?

   Both HBAs should see SPA_port_0 & SPB_port_0 and both HBAs should see SPA_port_1 & SPB_port_1 
   One HBA should see SPA_port_0 & SPA_port_1 while the other HBA should see SPB_port_0 & SPB_port_1 
   One HBA should see SPA_port_0 & SPB_port_0 while the other HBA should see SPA_port_1 & SPB_port_1 
v  One HBA should see SPA_port_0 & SPB_port_1 while the other HBA should see SPA_port_1 & SPB_port_0 

Which troubleshooting method is available for a Dell | EMC CX-600 but not for a Dell | EMC CX-400?

   Monitoring POST with a hyperterminal session. 
v  Port 80h codes 
   POST Alphabet 
   LED flash rate 

How many domains can a Dell | EMC CX-600 be a member of?

v  One 
   Two 
   Four 
   Three 

Which command will retrieve Navisphere Agent information from a Dell | EMC CX-600's storage processor whose IP address is 10.38.45.76?

   navicli getagent –h 10.38.45.76 
   navicli –h 10.38.35.76 agentget 
v  navicli –h 10.38.45.76 getagent 
   navicli –h 10.38.45.76 get agent 

Which PowerPath command will manually restore the paths in PowerPath?

   powermt failback 
v  powermt restore 
   powerpath restore 
   powermt trespass 

Which EMC utility is used to manage Emulex HBAs?

v  Elxcfg 
   Elconfig 
   Emlxcfg 
   Emconfig 

Which of the following is the correct method for configuring the network settings on a new CX600 array's Storage Processors?

   Use a serial PPP session to configure SP-A and reboot it. Repeat for SP-B. Reconnect to SP-A using PPP and restart the management server on SP-A. 
   Use a serial PPP session to configure SP-A and reboot it. Repeat for SP-B. Reconnect to SP-A using PPP and restart the management server. Repeat for SP-B 
v  Use a serial PPP session to configure SP-A and reboot it. Repeat the same configuration steps for SP-B. 
   Use a serial PPP session to configure SP-A and reboot it. Do not configure SP-B because it will obtain its network settings from SP-A automatically. 

What first must be done to change the storage domain membership of an already configured Dell | EMC CX600 array?

   Use the array's Navisphere Management UI to remove the array from its current domain. 
   Use your browser to connect to the domain master SP over a serial cable connection and remove the array from its current domain. 
   Perform a non-disruptive upgrade to reinstall the array's base code software. 
v  Use the array's Navisphere Management UI to reset the domain security. 

When installing a QLogic HBA in a Windows based server for direct attached storage, what must be true for the HBA's configuration?

v  The QLogic Loop - Auto Map driver must be installed. 
   The Connection Type BIOS setting must be set to 1. 
   The Connection Type BIOS setting must be set to 0. 
   The QLogic Fabric - Auto Map driver must be installed. 

How many longwave ISL's are required when cascading two Brocade DS32B2 switches?

   2 minimum, 4 maximum 
v  1 minimum, 4 maximum 
   Only 2 are supported 
   Only 1 is supported 

Which procedure is correct for zoning a McData switch in a Dell | EMC environment?

   Create a zone, add ports to the zone, add the zones to the zone set 
v  Create a zone, add WWNs to the zone, add the zone to the zone set 
   Create an alias, add the alias to the zone, add the zone to the config 
   Create a zone, add the zone to the alias, add the alias to the config 

What would the enclosure IDs be on a Dell | EMC CX700 array with 1 DAE-OS and 6 DAEs connected?

v  0,0,0,0,1,1,1 
   0,1,2,3,0,1,2 
   0,0,1,1,2,2,3 
   0,1,2,3,4,5,6 

When replacing an HBA in a server installed in a Dell | EMC SAN, what must be done for PowerPath to recognize the path of the new HBA?

   Remove the zone from the configuration, re-add it, then click enable. 
v  Remove the old member's WWN from the HBA's alias and add the new member's WWN. 
   Disable the configuration, add a new alias for the HBA and click enable. 
   Create a new zone for the HBA and add it to the existing configuration.