What would the enclosure IDs be on a Dell | EMC CX700 array with 1 DAE-OS and 6 DAEs connected?

   0,0,1,1,2,2,3 
   0,1,2,3,0,1,2 
v  0,0,0,0,1,1,1 
   0,1,2,3,4,5,6 

Which of the following is NOT a requirement when enabling write cache on a Dell | EMC storage array?

   Two Power Supplies in DPE 
   Functioning vault drives 
v  Two Fully charged SPS units 
   Two functional fan packs in DPE  

How many domains can a Dell | EMC CX-600 be a member of?

v  One 
   Two 
   Three 
   Four 

Which type of NaviSphere user account has read only rights on a CX700?

   Manager 
   Administrator 
v  Monitor 
   Reader 

Which parameters are required When connecting to a Dell | EMC DS-16-B2 (Brocade 3800) with a serial cable?

   Null modem ?9600, 8, None, 1, Hardware 
   Straight through cable ?2400, 8, None, 1, Hardware 
v  Straight through cable ?9600, 8, None, 1, None 
   Null modem ?2400, 8, None, 1, None 

Which command will retrieve Navisphere Agent information from a Dell | EMC CX-600's storage processor whose IP address is 10.38.45.76?

   navicli getagent –h 10.38.45.76 
   navicli –h 10.38.45.76 get agent 
   navicli –h 10.38.35.76 agentget 
v  navicli –h 10.38.45.76 getagent 

How is the PSM LUN created on a Dell | EMC CX-600?

   The PSM LUN is created the first time you connect with Navisphere Manager. 
   The PSM LUN is created using the http://192.168.1.1/setup pages. 
   The PSM LUN is created using the navicli command. 
v  The PSM LUN is created at the factory. 

What is the maximum number of supported DAE's that can be attached to a Dell | EMC CX-400?

   Two 
v  Three 
   Four 
   Five 

Which PowerPath license level is the minimum requirement to have front-end and back-end failover for a Dell | EMC CX700 installed in a Clariion only SAN?

   PowerPath Enterprise Plus 
   PowerPath Base 
   PowerPath Basic 
v  PowerPath Enterprise 

Which PowerPath command will manually restore the paths in PowerPath?

   powermt trespass 
   powerpath restore 
   powermt failback 
v  powermt restore 

What is the default username and password for a Navisphere 6.x domain?

v  There is no default username and password. 
   Username = admin and Password = password  
   Username = Administrator and password = password  
   Username = CLARiiON and password = CLARiiON! 

When installing a QLogic HBA in a Windows based server for direct attached storage, what must be true for the HBA's configuration?

   The QLogic Fabric - Auto Map driver must be installed. 
   The Connection Type BIOS setting must be set to 1. 
   The QLogic Loop - Auto Map driver must be installed. 
v  The Connection Type BIOS setting must be set to 0. 

Which of the following is the correct method for configuring the network settings on a new CX600 array's Storage Processors?

   Use a serial PPP session to configure SP-A and reboot it. Do not configure SP-B because it will obtain its network settings from SP-A automatically. 
v  Use a serial PPP session to configure SP-A and reboot it. Repeat for SP-B. Reconnect to SP-A using PPP and restart the management server on SP-A. 
   Use a serial PPP session to configure SP-A and reboot it. Repeat the same configuration steps for SP-B. 
   Use a serial PPP session to configure SP-A and reboot it. Repeat for SP-B. Reconnect to SP-A using PPP and restart the management server. Repeat for SP-B 

What first must be done to change the storage domain membership of an already configured Dell | EMC CX600 array?

   Use the array's Navisphere Management UI to reset the domain security. 
   Perform a non-disruptive upgrade to reinstall the array's base code software. 
v  Use your browser to connect to the domain master SP over a serial cable connection and remove the array from its current domain. 
   Use the array's Navisphere Management UI to remove the array from its current domain. 

A customer has added a new host to their Dell | EMC SAN. They have bound LUNs for the host to use and added the LUNs to a storage group, but the host does not have access to the LUNs. Navisphere shows the connectivity status of the HBAs in the host as blue. What needs to be done to provide the host access to the LUNs?

v  Add the host to the storage group with the luns. 
   Install and enable Access Logix. 
   Restart the Navisphere Agent service. 
   Edit the agent.config file and add privileged users.