=What rail options are available on the PowerVault NX1950? 4 post Sliding Rapid/Versa rail, 4 post Static Rapid/Versa, and 2 post Static = 4 post Sliding Rapid/Versa rail, 4 post Static Rapid or Versa, and 2 post Static 4 post Static Rapid or Versa, and 2 post Static 4 post Sliding Raid or Versa, and 4 post Static Rapid or Versa, and 2 post Static =How many and what type of PCI risers are in the PowerVault NX1950? 2; 1 PCI-e and 1 PCI-X = 2; 2 PCI-e risers 2; PowerVault NX1950 can configure as either 2 PCI-e or 2 PCI-X at purchase 2; 2 PCI-X risers =Why is it recommended to wait a period of time before removing the memory from a PowerVault NX1950? To allow the system board capacitance to discharge To allow the static to discharge from the memory To allow the FB-DIMMs to normalize = To allow the AMB time to cool down =Which keystroke(s) are used on BOOT to access the BIOS level interface to the PERC5/I on a PowerVault NX1950? = =You have just replaced a system board on a PowerVault NX1950, at boot up you see the message “FBD training error - The following memory branch has been disabled: Branch 0 ?what should you do next. = Reseat memory DIMMs 1,2,5,6 making sure they have good connections to the system board Reseat processor 1 making sure that they have good connections to the system board Reseat processor 2 making sure they have good connections to the system board Reseat memory DIMMs 3, 4, 7, 8 making sure they have good connections to the system board = Which type of hard disk drives are supported on the PowerVault NX1950? 3.5 inch SAS, 3.5 inch SATA and 2.5 inch SATA 3.5 inch SAS and 3.5 inch SATA = 3.5 inch SAS 2.5 inch SAS and 3.5 inch SATA =You want to replace the memory on a PowerVault NX1950 for a customer. What components must you remove before you can replace the memory? = Power source, chassis cover, and cooling shroud Power source, chassis cover, and center PCI riser Power source, chassis cover, and left PCI riser Power source, and chassis cover =What are the key strokes required to read the SEL log from inside of the BIOS? = Ctrl +E -> down arrow to system event log menu -> enter -> enter Ctrl +E -> tab to system event log menu -> enter -> tab to show event ->enter Ctrl +D -> tab to system event log menu -> enter -> tab to show event->enter Ctrl +D -> down arrow to system event log menu -> enter -> enter =What is the minimum to POST a PowerVault NX1950 for troubleshooting no post no video? System board, 2 processors, 2 sticks of memory, 2 power supplies, control panel, side plane, both PCI risers = System board, 1 processor, 1 stick of memory, 1 power supply, control panel, side plane, both PCI risers. System board, 1 processor, 2 sticks of memory, 1 power supply, control panel, side plane, both PCI risers System board, 2 Processors, 1 stick of memory, 2 power supplies, side panel, control, panel, both PCI risers =PowerVault NX1950 will start to POST then hang before it reaches the OS on the Dell NX1950 screen. There is nothing on the LCD screen except the default PowerVault NX1950 string message. What options do you have to determine what the issue might be? Go into the DRAC5 BIOS Go into the PERC5i BIOS = Hold down the “i?button for 5 seconds and read the error message on the LCD screen to diagnosis the system False Leaving the system on open the chassis cover, and use the LED’s on the system board to diagnosis the system