90% What components are field replaceable on the PowerConnect 5212? Power Supply v Network Switch Fan pack v SFP The PowerConnect 5224 has a red power LED illuminated when the internal power supply has failed. v True False On a PowerConnect 3248, which command would set a port to 10 Mb full duplex at the 'Console(config-if)#' prompt? speed 10full v speed-duplex 10full speed-duplex 100half speed-fullduplex 10mb A PowerVault 220S and a PowerVault 221S have indicator LEDs on which of the following modules? v The front panel The active cooling module The enclosure management module Split-bus module On the PowerEdge 6600, you can only remove and replace one power supply at a time when the system is powered on. v True False What is the embedded RAID option on a PowerEdge 4600? PERC 2/DI v PERC 3/DI PERC 3/SI PERC 2/SI If the ROMB hardware is installed, what system setup option on the PowerEdge 2650 allows you to enable or disable the embedded RAID controller? v Integrated devices Embedded server management PCI IRQ assignment Boot sequence What is the maximum number of processor(s) that can be installed in a PowerEdge 400SC? v One Two Three Four What is the cause of a 3-4-2 beep code error that occurs during a PowerEdge 400SC system startup? DMA initialization failure v Screen-retrace test failure or test in progress System configuration check failure Time of day-clock stopped What does a GATE A20 failure message indicate on the PowerEdge 650? NVRAM_CLR jumper is installed v Faulty keyboard controller Improperly installed memory module Bad mouse cable What must be replaced if the Time of Day clock fails on the PowerEdge 650? Power supply Backplane DIMMs v System board coin battery A blue blinking system status indicator on the PowerEdge 650 indicates? There is activity on the NIC The power is off A fault with the hard-disk drive v The system is identifying itself What does a 4-3-1 beep code indicate on the PowerEdge 1750? No memory installed Faulty mouse cable v Improperly installed, or faulty memory modules Cache test failure, or faulty microprocessor What system setup option on the PowerEdge 1750 allows you to set the maximum memory available to the operating system to 256 MB? Integrated devices PCI IRQ assignment Embedded server management v OS install mode How many processors will the PowerEdge 1750 support? One Four v Two Three When Array Manager is loaded on a system running Windows 2000 Server, what happens to the native disk management utility? v It is replaced by Array Manager. The native uutilities functionality is combined with Array Manager. The native utility operates in the backgroud. Nothing, both can be used. The SNMP community name cannot be specified during a Windows 2000 installation when using the Dell OpenManage Server Assistant CD. v True False What operating systems can IT Assistant be installed on? Red Hat Linux v Windows 2000 Professional v Windows XP Novell Netware What RAID level does NOT provide fault tolerance? RAID 0 RAID 1 v RAID 3 RAID 5 To install Server Administrator, you will need to select the Install Management Station button when prompted for Select System Type. v True False What functions can be performed from the Quick Access menu in Dell OpenManage Array Manager? Set policies Run Diagnostics v Create a volume v Remote Management What Server Administrator tab allows you to view the POST logs? Properties Diagnostics v Logs Shutdown The acronym RAID stands for: Redundant Array of Interconnected Disks Reliable Array of Inexpensive Drives v Redundant Array of Independent Disks Reliable Array of Inexpensive Disks To install IT Assistant, must select the Install Management Station button when prompted to select the system type. False v True The Diagnostic Service is installed by default when installing Server Administrator. False v True Dell OpenManage Array Manager manages storage resources on remote stations with the following operating system: v NT 4.0 Server Windows 98 Netware 5.0 v Windows 2000 Advanced Server hen a new version of IT Assistant is installed over an older one, the installation program saves the current IT Assistant database. False v True Array Manager supports AMI/LSI and Adaptec based PERCs. False v True Which keys must be pressed to access the PERC 2, 2/Si, 3/Si or 3/Di BIOS configuration utility? v Which of the following firmware interfaces are available on the PERC 3/DCL, PERC, 3/DC, and PERC 3/QC? Ctrl-Q: Quick Setup Utility v Ctrl-M: Adapter BIOS Utility v Ctrl-H: WebBIOS Utility Ctrl-G: GUI BIOS Utility