The PowerEdge 2450 supports embedded RAID. # True. False. On the PowerEdge 2450, processor slot that is not filled by a processor is required to be filled with a terminator card. True. # False. How many PS/2 compatible mouse ports are integrated in the PowerEdge 1550? # One. Two. None. Three. On the PowerEdge 1550, the backplane is secured to the chassis by: Three Phillips-head screws. # Two thumbscrews. A thumbscrew and latch. A latch. How many full-length PCI cards can be installed in the PowerEdge 1550? Three. Two. Four. # One. Does the PowerEdge 1550 support four internal hard disk drives? Yes. # No. In the PowerEdge 1550, the PERC3 DCL cache has a battery backed up. # False. True. On the PowerEdge 2400, which of the following components are located on the system board? # Video. #SCSI controller. DRAC. #NIC. The PowerEdge 2400 supports embedded RAID. # True. False. To remove a redundant power supply on the PowerEdge 2400, which one of the following components must first be removed? The front bezel. # Nothing is needed to be removed first. The hard drive fan assembly. The left side panel. To remove the hard drives on the PowerEdge 2400, which one of the following components must first be removed? The left side panel. # The front bezel. The hard drive fan assembly. The power cabling harness. To remove the SCSI backplane on the PowerEdge 2400, which one of the following components must first be removed? The hard drive fan assembly. The left side panel. # The hard-disk drives. All installed PCI cards. To remove the power supply on the PowerEdge 6450, which one of the following components must first be removed? The left side panel. # Nothing hs to be removed. The hard drive fan assembly. The right hinged door The PowerEdge 6450 system fan is hot swappable. True. # False. To remove the system board on the PowerEdge 6450, which one of the following components must first be removed? The hard-disk drives. # The memory board. The control panel. The front bezel. To remove a processor on the PowerEdge 2550, which of the following operations must be performed? The control panel. Remove the hard drive fan assembly. #Disconnect the AC adapter. Remove the front bezel. The RAID On Motherboard (ROMB) battery for the PowerEdge 2550 is secured to the chassis by a ____ . # A clip. ZIF socket on the system board. Soldered to the system board. Thumbscrew The memory VRM on the PowerEdge 2550 is secured in the slot by____ . # Two clips. A thumbscrew. Two phillips-head screws. A retaining bracket. On the PowerEdge 4400, the power supplies are secured to the chassis by? A thumbscrew. A thumbscrew and latch. # A latch. Three Phillips-head screws. On the PowerEdge 4400, the system board is secured to the chassis by? A latch. Three Phillips-head screws. A thumbscrew and latch. # A thumbscrew. On the PowerEdge 4400, prior to replacing a processor, what must be done to the PowerEdge 4400, to ensure the procedure is completed safely? Nothing, the processor is hot-pluggable. Ground yourself to the PowerEdge 4400 only. Unplug the AC power cable only. # Power down and unplug the AC power. The PowerEdge4400 contains the following Embedded RAID controller? PERC 2/Di PERC 3/Si # PERC 3/Di PERC 2/Si What is the maximum time allowed to remove the hard-disk drive fan assembly? # Two minutes. One minute. Three minutes. Two seconds. The PowerEdge 2500 supports which of the following processor types? Pentium III Xeon. Pentium 4. Pentium Pro. # Pentium III. Which of the following steps must be performed prior to removing a PowerEdge 2500 from an equipment rack? # Unscrew the rails from the side of the system. # Disconnect the cable management arm from the system and the rack. # Power down the system. Remove the side panels from the rack. To remove a redundant power supply on the PowerEdge 2500, which one of the following components must first be removed? The control panel. The side panel. The hard drive fan assembly. # The front bezel. The PowerVault 211S is configured as a rack mount unit. True. # False. The processor heatsink on the PowerEdge 2500 is secured to the processor by ________ . Rivets. Thermal adhesive. # A clip. Thumbscrew. The power supplies on the PowerVault 210S/211S are hot swappable. # True. False. To remove the hard drives on the PowerVault 210S/211S, which one of the following components must first be removed: The power cabling harness. The ES module. The hard drive fan assembly. # The hard drive locking bar. To remove a cooling fan on the PowerVault 210S/211S, which one of the following components must first be removed? # Nothing has to be removed. ES module. The hard-disk drives. Power Supply. To remove the mid-plane board on the PowerVault 210S/211S, which of the following components must first be removed? # Power Supplies. Nothing has to be removed. The hard-disk drives. # Cooling fans. The RAID On Motherboard (ROMB) enabler key, for the PowerEdge 2500 is secured to the chassis by ________ . # Two blue tabs on a ZIF socket. A thumbscrew and latch. A thumbscrew. A latch. The minimum and maximum amounts of memory that can be installed in a PowerEdge 6450 are: # 256 MB and 8 GB. 128 MB and 2 GB. 512 MB and 8 GB. 256 MB and 4 GB. On the PowerEdge 6450, which of the following components are located on the PowerEdge 6450 system board? # Adaptec 7899 SCSI controller. # Intel Pro/100+ NIC. Audio. Server Management Port.